Harry Potter Tea Towel Bag – How To. 

I received a set of Harry Potter tea towels as a gift and my little brain starting whirling… there was no way that I could even contemplate using those bad boys to wipe dishes and so I hatched a plan and turned these: 


Into this: 


Now I shared this on a couple of the craft sites I’m a part of on Facebook and a few people asked me for a tutorial on how to make these. I have NEVER done a tutorial before but I thought why not and so here it goes. 

You will need: 

Materials:

  • 1 Harry Potter Tea Towel (or any other fabric of your choice for the outside of the bag) 
  • Lining fabric – the size of this will depend on how big you want your bag. I brought half a meter of black fabric and also used this for the shoulder strap. 
  • Zip – again dependant on size required although I used a 12 inch zip. 
  • Heavy weight interfacing. 
  • Cotton to match – I used black. 
  • Lobster Swivel Clasps (I used 3) 

Tools: 

  • Sewing machine 
  • Fabric scissors 
  • Ruler 
  • Pins 

To start: 

Cut your bag pieces. You will need 2 of the outer fabric, 2 of the lining and 2 of the interfacing. I cut mine 12 inches wide (the same length as my zip) by 10 inches tall. To give the shape to the bottom I cut out a 1 inch square out of the bottom corners of each fabric piece. 

You should be left with 6 pieces like this (excuse the awful drawing). 


If you wanted to make your bag straight without the shape to the bottom them you still cut out the fabric pieces in the size you want but you miss out the squares in the bottom corners. 

You will also need to cut 2 small pieces around 2 inches by an inch out of your outer material which are for your straps and I cut out a piece out of the outer fabric around 50cm x 1 inch for the hand strap. 

The across body / shoulder strap should be cut to your desired length and about 1 inch wide.

First you will need to sew your zip to your fabrics. To do this place your interfacing under your lining fabric (with the wrong side of the lining fabric facing the interfacing and then place the zip on top. ​​


You the need to place your outside fabric on top of the zip with the right side of the fabric facing the zip and pin along the edge and sew. 


Repeat this for the other side of the zip. 

Once you have sewn all of your fabric to your zips you should sew your small pieces of outer fabric that are for your straps. You should fold the 2 outside edges so that they meet in the middle and then fold the fabric in half so that the two raw edges are inside. You should then sew along the open edge to create the tabs for your straps – these will look like this when it’s finished: 


Your across body strap and wrist strap should be sewn in the same way as these and can be done at this stage. 

Now to sew your bag together you should open your zip and the place your pieces together with right sides together and pin. While pinning you should put your two tab pieces between the two outer pieces in a loop and pin. When pinned it should look like this: 


You should sew along the edges as shown in the image above by the arrows leaving a 3 inch gap at the bottom of the lining fabric for turning. If you have not left the squares at the bottom you can sew all of the sides together just leaving the gap.

Once you have done this you will need to sew your bottom corners. You should do this on both the lining/interfacing and the outside fabric. You do this by pulling the side and bottom seam together so that the seams match and then sewing closed – for extra reinforcement you can sew along this line twice. 

I’ve stolen an image from google images that sort of shows this: 


One you have done this you can turn the bag and sew the gap closed. 

All that is left to do now is to sew your lobster clasp to your straps. You do this by putting the end of your strap through the hole on your lobster clasp and sewing the two pieces together. I used a zigzag stitch and made sure that this went over the raw edge to prevent fraying. I also went over this a couple of times for reinforcement. 

Your bag should now be finished 🙂 

I’m not used to writing tutorials like this so if anything doesn’t make sense please ask 🙂 

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s